CSCS Plumbing Mock Test

0 votes, 0 avg

Specialists Test

Plumbing

1 / 37

What should you do if you arrive at a job which involves using ladder access to the roof and you notice that the ladder has been painted?

Only use the ladder if it is made of metal

Only use the ladder if it is made of wood

Not use the ladder, and report the matter to your supervisor

Only use the ladder if wearing rubber-soled boots to prevent slipping

2 / 37

What should you do when using a blowtorch near to flexible pipe lagging?

Remove just enough lagging to carry out the work

Remove the lagging at least 3 m either side of the work

Wet the lagging but leave it in place

Remove the lagging at least 1 m either side of the work

3 / 37

When is it safe to transport workers to the workplace in the rear of a van?

When the driver is over 21 years of age

When the van is fitted with temporary seating

When the van is fitted with proper seating and seat belts

When the driver has a heavy goods vehicle licence

4 / 37

You are preparing to use an electric-powered threading machine. Which of the following statements should apply?

The power supply should be 400 volts and the machine fitted with a guard

The power supply should be 24 volts and the machine fitted with a guard

Ear defenders should be available and should be in good condition

Ensure your clothing cannot get caught on rotating parts of the machine

5 / 37

Which of the following statements is true?

Both propane and butane are lighter than air

Both propane and butane are heavier than air

Butane is heavier than air while propane is lighter than air

Propane is heavier than air while butane is lighter than air

6 / 37

When replacing an electrical immersion heater in a hot water storage cylinder, what should you do to make sure that the electrical supply is dead before starting plumbing work?

Switch off and cut through the electric cable with insulated pliers

Switch off and disconnect the supply to the immersion heater

Switch off, isolate the supply at the mains board and test the circuit

Switch off and test the circuit

7 / 37

What should you do if you need to move a cast iron bath, but it is too heavy to lift by yourself?

Try and find someone to give you a hand

Give it another try

Get a lifting accessory

Inform your supervisor and ask for assistance

8 / 37

If you are asked to move a cast iron boiler some distance, what should you do?

Roll it end-over-end

Drag it

Get a workmate to carry it

Use a suitable trolley or other manual handling aid

9 / 37

What piece of equipment would you use to find out whether a section of solid wall that you are about to drill into contains electric cables?

A neon screwdriver

A multimeter

A hammer and chisel

A cable tracer

10 / 37

How are legionella bacteria passed on to humans?

From other people when they sneeze

By drinking dirty water

Through fine water droplets, such as sprays or mists

Through contact with the skin

11 / 37

While working, you come across a hard, white, powdery material that could be asbestos. What should you do?

Stop work immediately and tell your supervisor about the material

Dampen the material down with water and remove it before carrying out the work

While wearing respiratory protective equipment, remove the material and dispose of it safely

Remove the material, putting it back after finishing the job

12 / 37

If you are required to re-fix a section of external rainwater pipe using a power drill in wet weather conditions, which type of drill is most suitable?

Drill with 110-volt power supply

Battery-powered drill

Any mains voltage drill with a power breaker

Drill with 240-volt power supply

13 / 37

You are drilling a 100 mm diameter hole for a flue pipe through a brick wall with a large hammer drill. Which combination of personal protective equipment (PPE) should you be supplied with?

Gloves, breathing apparatus and ear defenders

Ear defenders, respiratory protective equipment and barrier cream

Ear defenders, respiratory protective equipment and eye protection

Barrier cream, boots and respiratory protective equipment

14 / 37

If working on a plumbing job where noise levels are rather high, who would you expect to carry out noise assessment?

Your supervisor

The site engineer

A competent person

A fully qualified plumber

15 / 37

Where is the safest place to store oxyacetylene gas-welding bottles when they are not in use?

In the immediate work area, ready for use the next day

In company vehicles

Inside the building in a locked cupboard

Outside in a special storage compound

16 / 37

What is the preferred method of checking for leaks when assembling liquefied petroleum gas (LPG) equipment before use?

Apply leak detection fluid to the connections

Sniff the connections to detect the smell of gas

Listen to hear for escaping gas

Test with a lighted match

17 / 37

What is the colour of an acetylene cylinder?

Green

Orange

Maroon

Black

18 / 37

Which of the following makes it essential to take great care when handling and transporting oxygen cylinders?

They contain highly flammable compressed gas

They are filled to extremely high pressures

They contain highly flammable liquid gas

They contain poisonous gas

19 / 37

If you are drilling a hole, when do you need to wear eye protection?

Always, whatever the circumstances

Only when drilling through concrete

Only when drilling overhead

Only when the drill bit exceeds 20 mm

20 / 37

The use of oxyacetylene equipment is not recommended for which of the following jointing methods?

Jointing mild steel tube

Jointing copper pipe using hard soldering

Jointing copper tube using capillary soldered fittings

Jointing sheet lead

21 / 37

Why is it important that operatives know the difference between propane and butane equipment?

Propane equipment operates at higher pressure

Propane equipment can be used with smaller, easy-to-handle cylinders

Propane equipment is cheaper

Propane equipment operates at lower pressure

22 / 37

Where should a fire extinguisher be if you are using a blowtorch to joint copper tube and fittings in a domestic property?

In your vehicle, as long as the doors are locked

There is no need for a fire extinguisher

Available in the immediate work area

Available only if a property is occupied

23 / 37

If you have been handling sheet lead, what is the most likely way lead could get into your bloodstream?

By not using the correct respirator

By not changing out of your work clothes

By not wearing safety goggles

By not washing your hands before eating

24 / 37

How should you install a flue into an existing chimney?

Work in pairs and insert the liner from roof level, working off the roof

Insert the liner from roof level using a roof ladder

Break through the chimney in the loft area and insert the liner from there

Work in pairs and insert the liner from roof level, working from a chimney scaffold

25 / 37

Which is the safest method of transporting long lengths of copper pipe by van?

Using a pipe rack fixed to the roof of the van

Putting the pipes inside the van with the ends out of the passenger window

Someone holding the pipes on the roof rack as you drive along

Tying the pipes to the roof with copper wire

26 / 37

If lifting a roll of Code 5 sheet lead, what is the first thing you should do?

Ask your workmate to give you a hand

Have a trial lift to see how heavy it feels

Assess the whole task

Weigh the roll of lead

27 / 37

What should you do if you are using a blowtorch near to timber?

Use a non-combustible mat and have a fire extinguisher ready

Point the flame away from the timber and have a bucket of sand ready to put out the fire

Carry out the work taking care not to catch the timber

Wet the timber first and have a bucket of water handy

28 / 37

What should you do when repairing a burst water main using pipe-freezing equipment to isolate the damaged section of pipe?

Never allow the freezing gas to come into direct contact with surface water

Wear gloves to avoid direct contact with the skin

Always work in pairs when using pipe-freezing equipment

Never use pipe-freezing equipment on plastic pipe

29 / 37

Why should you carry out temporary continuity bonding before removing and replacing sections of metallic pipework?

To provide a continuous earth for the pipework installation

To maintain the live supply to the electrical circuit

To prevent any chance of blowing a fuse

To prevent any chance of corrosion to the pipework

30 / 37

You are required to replace below-ground drainage pipework in an excavation, which is approximately 2.5 m deep, but the trench sides show signs of collapse. What should you do?

Refuse to do the work until the trench sides have been properly supported

Get on with the work as quickly as possible

Ensure that you do the work with a rope around you so that you can be pulled out

Get a mate to help you so that they can pass the materials down to you

31 / 37

What is the most likely risk of injury when cutting large diameter pipe?

You may cut yourself on the inside edge of the cut pipe

Your fingers may become trapped between the cutting wheel and the Pipe

A piece of sharp metal could fly off and hit you

You may damage your muscles due to continued use

32 / 37

Apart from the cylinders used in gas-powered forklift trucks, why should liquefied petroleum gas (LPG) cylinders never be placed on their side during use?

The liquid gas would be at too low a level to allow the torch to burn correctly

It would give a faulty reading on the contents gauge, resulting in flashback

Air could be drawn into the cylinder, creating a dangerous mixture of gases

The liquid gas could be drawn from the cylinder, creating a safety hazard

33 / 37

The legionella bacteria that cause legionnaires' disease are most likely to be found in which of the following?

A shower hose outlet

A toilet pan

A boiler operating at a temperature of 80°C

A cold water storage cistern containing water at 10°C

34 / 37

How should bottles be positioned when using oxyacetylene welding equipment?

Angled at 45°

Laid on their side and secured

Stood upside down

Stood upright and secured

35 / 37

You are working in an occupied building and have taken up six lengths of 3 m floor boarding when you are called away to an urgent job. What should you do?

Cordon off the work area before leaving the job

Permanently re-fix the floorboards and floor coverings

Leave the job as it is

Tell other workers to be careful while you are away

36 / 37

Which item of personal protective equipment (PPE) is designed to protect against infrared radiation damage to the eyes during flame cutting or welding?

Impact-rated safety goggles

Eye protection with a tinted or filter lens

Reflective vest

Respiratory protective equipment (RPE)

37 / 37

You are removing guttering from a large, single-storey, metal-framed and cladded building and the job is likely to take all day. What is the most appropriate type of access equipment you could use?

A mobile access tower

A ladder

A trestle scaffold

A putlog scaffold

Your score is

The average score is 69%

Exit

How was the test? Please Submit your Rating and give us a feedback!

Thank you for taking the time to complete a mock test on our website. We appreciate your effort and dedication.

We wish you the best of luck in your preparation and future exams. If you have any feedback or suggestions, please let us know.

CSCS Plumbing Mock Test – Get Ready for Your CSCS Plumbing Card

What is the CSCS Plumbing Test?

The CSCS Plumbing Test is a specialist Health, Safety and Environment (HS&E) test designed for plumbers working on construction sites. It checks your understanding of health and safety practices specific to plumbing work, helping ensure a safe working environment.